Catalogue de produits

Form-A-Barrier solves the problem of needing a light weight, formable shield to protect components from heat. Light weight, formable, rigid shield provides excellent thermal protection up to 1300F with minimal gap of 1 inch to heat source. Can be formed or bent by hand to conform to odd shapes. Mechanically fasten with pins, screws or bolts.

Form-A-Barrier solves the problem of needing a light weight, formable shield to protect components from heat. Light weight, formable, rigid shield provides excellent thermal protection up to 1300F with minimal gap of 1 inch to heat source. Can be formed or bent by hand to conform to odd shapes. Mechanically fasten with pins, screws or bolts.

A high temperature resistant braided glass material, woven into a sleeve and heavily coated with 100% silicone rubber with 304 stainless mesh outer covering, EXO Sleeve provides the ultimate in heat insulation and protection from direct heat up to 500F.

A high temperature resistant braided glass material, woven into a sleeve and heavily coated with 100% silicone rubber with 304 stainless mesh outer covering, EXO Sleeve provides the ultimate in heat insulation and protection from direct heat up to 500F.

Thermal Sensor and Wire connector covers are a great way to protect sensors plugs and wire connectors from heat, moisture and dirt. They are made from an aluminized insulation that will reflect heat and act as a thermal barrier for sensitive wire connections and sensors.

Thermal Sensor and Wire connector covers are a great way to protect sensors plugs and wire connectors from heat, moisture and dirt. They are made from an aluminized insulation that will reflect heat and act as a thermal barrier for sensitive wire connections and sensors. Simple to install with a split top to cover connectors near engine manifolds, turbos, and their heat sources. Includes: Two (2) covers, 32mm I.D. x 2 in. with 35.2mm O.D.

Thermal Sensor and Wire connector covers are a great way to protect sensors plugs and wire connectors from heat, moisture and dirt. They are made from an aluminized insulation that will reflect heat and act as a thermal barrier for sensitive wire connections and sensors. Simple to install with a split top to cover connectors near engine manifolds, turbos, and their heat sources. Includes: Two (2) covers, 25mm I.D. x 2 in. with 28.2mm O.D.

Cool Tape(TM) is a flexible and super strong self-adhesive thermal insulating tape capable of protecting up to 2000F of radiant heat. Made of one mil aluminized material bonded to a woven glass fiber heat resistant matting, Cool Tape(TM) is a ultra light weight heat reflective solution for wrapping wires, cables, hoses, fuel lines, covering seams and many other uses. Withstands direct heat up to 400F Use to secure panels, seal air boxes, wrap wiring & more Strong self-adhesive backing Perfect for giving Reflect-A-Cool, Heat Screen and Floor & Tunnel Shield II a finished edge look! DO NOT apply directly to exhaust components.

Protects Dynamometer tie-down straps from burn-through caused by exhaust exit heat Made of a hi-temp resistant aluminized mylar material Withstands 500F direct / 2000F radiant heat Easily slips over dyno tie down straps 36 in. long x 5 in. wide

Cool Cover(TM) is designed to prevent air tubes from becoming heat sinks. Made of heat treated glass fiber with a reflective coating, Cool Cover(TM) will reflect radiant heat from air tubes and promotes a cooler, denser, more powerful air charge. With a unique full length hook & loop closure design, Cool Cover(TM) can be removed in seconds without the need of any hand tools! Reflects heat from air tubes Promotes cooler air charge for added power Installs & removes in seconds for show or go Fits up to 4 in. diameter tubing Up to 4 in. O.D. x 36 in. L

Fuel Injector and sensor covers solve the problem of rough idle, stalling and vapor lock due to hot fuel. In hot temps, both performance and factory fuel injectors can be at risk of vapor lock or heat soak causing a rough idle, slow starting or other potential serious engine problems. DEI has the solution by introducing Fuel Injector Reflective Heat Covers available in packs of two, four, six or eight, that reflect direct and radiant heat away from the injectors.

HT Silicone Coatings solve the problem of exhaust wraps deteriorating because of dirt and debris hitting it. It seals and protects wraps and extends the life of the wrap. The High Temperature (HT) Silicone Coating provides lasting protection for any hot surface up to 1200 degrees. DEI recommend the use of this coating with their exhaust wrap because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home.