Nous utilisons des témoins pour améliorer votre expérience. Pour respecter les directives de vie privée en ligne, nous vous demandons de consentir à ces derniers. Learn more.
Design Engineering
-
Sku: DEI 109080 In StockUPC: 607078109088Fabricant: Design Engineering
Versa-Shield was designed to protect starters from potential failure caused by under hood heat soak conditions. Constructed using an aluminized heat reflective material backed with a hi-temp rated glass fiber insulation barrier, Versa-Shield is capable of reflecting radiant heat up to 2000F. Simply wrap desired component with Versa-Shield and trim excess material. Edges attach to itself using a hook & loop edge closure design. In most cases there is no need to remove component when installing Versa-Shield.
Learn More -
Sku: DEI 504490 In StockUPC: 607078504494Fabricant: Design Engineering
Boom Mat Tape has the same noise blocking and sound damping qualities as our Boom Mat damping material. It's for those hard to reach areas as well as for covering wire and cable harnesses running on or along the sides of floorboards. Boom Mat Tape is a multi-purpose sound deadening material for use anywhere to help reduce road noise, sound system vibrations, rattles, dash board plastic-to-plastic chafing sounds, door panels, floor pans, deck lids and trunk area to name a few. There are many in-home uses for Boom Mat Tape as well.
Learn More -
Sku: DEI 936010 In StockUPC: 607078936011Fabricant: Design Engineering
Protect expensive spark plug wire sets from potential burning, cracking, and hardening typically caused by severe under hood heat. Easily installs on wire by removing distributor boot and sliding Protect-A-Wire(TM) over spark plug wire. Buy in bulk with these 50 foot rolls of Protect-A-Wire. Great for shop use so Protect-A-Wire(TM) is always in stock.
Learn More -
Sku: DEI 934870 In StockUPC: 607078934871Fabricant: Design Engineering
Heat Shroud(TM) solves the problem of heat and abrasions causing failure of lines, hoses and wires without the need to disconnect them. Heat Shroud is made from a high temperature rated glass fiber fabric with an aluminized outer facing. Same as Heat Sheath but with the added convenience of hook & loop closure design along the open edges. Without the need of removing one end of connected wires, cables and hoses, simply wrap Heat Shroud around whatever needs protection and close edges.
Learn More -
Sku: DEI 934200 In StockUPC: 607078934208Fabricant: Design Engineering
Heat Sheath(TM) solves the problem of heat and abrasions causing failure of lines, hoses & wires. Designed to slide over wires, cables and hoses, Heat Sheath provides the ultimate protection from extreme heat as well as chemical and oil spills, dirt, grease and road grime. Constructed from a high temperature fabric and bonded to an aluminized material to reflect heat. Heat Sheath is fireproof and withstands direct heat up to 500F.
Learn More -
Sku: DEI 934190 In StockUPC: 607078934192Fabricant: Design Engineering
Heat Sheath(TM) solves the problem of heat and abrasions causing failure of lines, hoses & wires. Designed to slide over wires, cables and hoses, Heat Sheath provides the ultimate protection from extreme heat as well as chemical and oil spills, dirt, grease and road grime. Constructed from a high temperature fabric and bonded to an aluminized material to reflect heat. Heat Sheath is fireproof and withstands direct heat up to 500F.
Learn More -
Sku: DEI 934180 In StockUPC: 607078934185Fabricant: Design Engineering
Heat Sheath(TM) solves the problem of heat and abrasions causing failure of lines, hoses & wires. Designed to slide over wires, cables and hoses, Heat Sheath provides the ultimate protection from extreme heat as well as chemical and oil spills, dirt, grease and road grime. Constructed from a high temperature fabric and bonded to an aluminized material to reflect heat. Heat Sheath is fireproof and withstands direct heat up to 500F.
Learn More -
Sku: DEI 934050 In StockUPC: 607078934055Fabricant: Design Engineering
Heat Shroud(TM) solves the problem of heat and abrasions causing failure of lines, hoses and wires without the need to disconnect them. Heat Shroud is made from a high temperature rated glass fiber fabric with an aluminized outer facing. Same as Heat Sheath but with the added convenience of hook & loop closure design along the open edges. Without the need of removing one end of connected wires, cables and hoses, simply wrap Heat Shroud around whatever needs protection and close edges.
Learn More -
Sku: DEI 934040 In StockUPC: 607078934048Fabricant: Design Engineering
Heat Sheath(TM) solves the problem of heat and abrasions causing failure of lines, hoses & wires. Designed to slide over wires, cables and hoses, Heat Sheath provides the ultimate protection from extreme heat as well as chemical and oil spills, dirt, grease and road grime. Constructed from a high temperature fabric and bonded to an aluminized material to reflect heat. Heat Sheath is fireproof and withstands direct heat up to 500F.
Learn More -
Sku: DEI 934030 In StockUPC: 607078934031Fabricant: Design Engineering
Heat Sheath(TM) solves the problem of heat and abrasions causing failure of lines, hoses & wires. Designed to slide over wires, cables and hoses, Heat Sheath provides the ultimate protection from extreme heat as well as chemical and oil spills, dirt, grease and road grime. Constructed from a high temperature fabric and bonded to an aluminized material to reflect heat. Heat Sheath is fireproof and withstands direct heat up to 500F.
Learn More -
Sku: DEI 916010 In StockUPC: 607078916013Fabricant: Design Engineering
Protect expensive spark plug wire sets from potential burning, cracking, and hardening typically caused by severe under hood heat. Easily installs on wire by removing distributor boot and sliding Protect-A-Wire(TM) over spark plug wire. Buy in bulk with these 50 foot rolls of Protect-A-Wire. Great for shop use so Protect-A-Wire(TM) is always in stock.
Learn More -
Sku: DEI 107020 In StockUPC: 607078107022Fabricant: Design Engineering
Protect-A-Boots solve the problem of burning and cracking plug boots and wires from header and engine heat. Each kit includes everything needed to protect spark plug boots and wires from harmful under hood heat. Color matched Protect-A-Boots, Protect-A-Wire and Hi-Temp Shrink Tubes are included for a professional finished look. Our 6'' Protect-A-Boots come with a reinforcement ring at the base for easy plug removal during maintenance. When working on boots with tight bends, try our ringless 8'' Protect-A-Boot (only in silver or Titanium(TM)) instead. For thicker boots, like MSD or Taylor's, we recommend our Protect-A-Boot(TM) Sleeves.
Learn More -
Sku: DEI 107010 In StockUPC: 607078107015Fabricant: Design Engineering
Protect-A-Boots solve the problem of burning and cracking plug boots and wires from header and engine heat. Each kit includes everything needed to protect spark plug boots and wires from harmful under hood heat. Color matched Protect-A-Boots, Protect-A-Wire and Hi-Temp Shrink Tubes are included for a professional finished look. Our 6'' Protect-A-Boots come with a reinforcement ring at the base for easy plug removal during maintenance. When working on boots with tight bends, try our ringless 8'' Protect-A-Boot (only in silver or Titanium(TM)) instead. For thicker boots, like MSD or Taylor's, we recommend our Protect-A-Boot(TM) Sleeves.
Learn More -
Sku: DEI 104020 In StockUPC: 607078104021Fabricant: Design Engineering
Versa Shields(TM) solve the problem of failing starters and other components due to heat soak. Versa Shield was designed to protect starters from potential failure caused by under hood heat soak conditions. Constructed using an aluminized heat reflective material backed with a hi-temp rated glass fiber insulation barrier, Versa-Shield is capable of reflecting radiant heat up to 2000F. Simply wrap desired component with Versa-Shield and trim excess material.
Learn More -
Sku: DEI 106690 In StockUPC: 607078106698Fabricant: Design Engineering
Vapor Block(TM) solves the problem of fuel and other fluids boiling from extreme heat and causing a vapor lock situation. Prevent rough idling and difficult starting caused by vapor lock with DEI Vapor Block(TM). Vapor Block(TM) fuel line sleeve was specifically developed to prevent vapor lock in fuel systems by greatly reducing heat in the line to keep fuel cooler and below boiling. Vapor Block(TM) installs easily with a split design and adhesive flap.
Learn More